Efecto del tratamiento de la morfología oclusal con materiales para restauraciones preventivas / Effect of treating occlusal morphology with materials for preventive restorations

Introducción: las fosas y fisuras son áreas formadas por delgadas irregularidades de la capa del esmalte de la superficie oclusal. La compleja morfología en dientes posteriores es un determinante biológico asociado al desarrollo de caries. Objetivo: evaluar el efecto de diversas formas de tratar la morfología oclusal en la adaptación y penetración de materiales utilizados en restauraciones preventivas. Material y métodos: diseño experimental e in vitro. Sesenta terceros molares fueron distribuidos aleatoriamente en dos grupos: surco sin ameloplastia y con ameloplastia; además, contaban con acondicionamiento del esmalte que se subdividió en tres subgrupos: 1) sellador de fosas y fisuras, 2) adhesivo/sellador de fosas y fisuras y 3) adhesivo/ resina Flow. Resultados: los subgrupos adhesivo/sellador y adhesivo/ Flow alcanzaron mayores valores de adaptación íntima a las paredes del surco. Las diferencias fueron significativas entre los materiales (p = 0.0009). Las mayores zonas de desadaptación resultaron para el sellador sin y con ameloplastia. La penetración de los materiales fue mayor en los surcos con ameloplastia. En los surcos tratados con ameloplastia, el adhesivo/Flow reveló el mayor porcentaje de penetración y la mejor adaptación a las paredes del surco. Conclusiones: la penetración del material está positivamente correlacionada con la profundidad del surco. El sellador con y sin ameloplastia mostró pobre adaptación a las paredes del surco (AU)

Introduction: pits and fissures are areas formed by fine irregularities in the enamel layer of the occlusal surface. The complex morphology in posterior teeth are biological determinants associated with the development of caries. Objective: to evaluate the effect of various ways of treating occlusal morphology on the adaptation and penetration of materials used in preventive restorations. Material and methods: experimental design, in vitro. Sixty third molars were randomly distributed into two groups: groove without ameloplasty and with ameloplasty, with enamel conditioning with three subgroups: 1) pit and fissure sealer, 2) adhesive/pit and fissure sealer, 3) adhesive/resin flow. Results: the adhesive/sealant and adhesive/flow subgroups reached higher values of intimate adaptation to the furrow walls. The differences were significant between the materials (p = 0.0009). The largest areas of maladjustment were found for the sealant without and with ameloplasty. The penetration of the materials was greater in the grooves with ameloplasty. In the grooves treated with ameloplasty, the adhesive/flow revealed the highest percentage of penetration and the best adaptation to the walls of the groove. Conclusions: the penetration of the material is positively correlated with the depth of the furrow. The sealant with and without ameloplasty showed poor adaptation to the sulcus walls (AU)

Comparative Study of the Shear Bond Strengths and Bracket Failure Rates of Two Orthodontic Adhesive Systems

Abstract Objective: To evaluate and compare the shear bond strengths (SBS) and bracket failure rates (BFR) of orthodontic brackets bonded with Light Cure adhesive against those bonded with Self Cure adhesive. Material and Methods: The study had in vitro and in vivo parts. In the in vitro part to determine SBS of Light Bond(LB)(R) and Rely.a.Bond(RB)(R) adhesives used in bonding brackets to 88 extracted teeth, each adhesive type was used to bond 44 brackets. The clinical study was conducted to determine the BFR of the LB(R) and RB(R) adhesives by bonding 256 teeth using each adhesive type. A standardized bonding procedure was followed in both the in vitro and in vivo parts of the study. Data were analyzed using frequency, percentage, mean, independent t-test, chi-square, and Pearson Correlation statistics. A p-value of ≤ 0.05 was considered significant. SPSS version 21.0 was used to analyze the data generated. Results: There was a significantly higher mean SBS 10.6MPa for LB(R) adhesive than the 7.0MPa of the RB(R) adhesive. In the in vivo study, (LB)(R) had a greater but not significant BFR of 9.0% than RB(R) (8.0%). No significant relationship existed between the SBS of either adhesive type (as determined in vitro) and their BFR in vivo. Conclusion: Higher SBS of LB(R) did not translate to less BFR in the clinic, nor did a lower SBS of RB(R) translate to more BFR in the clinic (AU).

Micron-scale human enamel layer characterization after orthodontic bracket debonding by intensity-based layer segmentation in optical coherence tomography images.

In clinical orthodontic practice, fixed brackets are widely used for tooth movement and adjustments. Although years of research and development have improved the workability of fixed orthodontic brackets, there are still controversies regarding its plausible destructive influence on the enamel surface of tooth. This, in turn, makes the quantitative assessment of the enamel surface after specific orthodontic treatment procedures important in order to opt for the most effective treatment procedure. Through this study, we show the practical applicability of optical coherence tomography (OCT) as a non-ionizing and nondestructive assessment tool for measuring enamel loss after each step of orthodontic bracket bonding. Two-dimensional and volumetric OCT images are used for the evaluation of the tooth enamel. From the depth intensity profile analysis of cross-sectional OCT images, the changes in the individual internal layer thickness are calculated. A software algorithm was developed to evaluate the structural connectivity in the enamel for analyzing enamel loss on the tooth surface and for detecting enamel abrasion. An intensity-based layer segmentation algorithm is also developed to analyze and evaluate enamel wear in the tooth after each step. Using the proposed algorithms, the total enamel present after each treatment procedure was measured and tabulated for analysis.

Eficacia del cementado indirecto / Indirect bonding efficiency

La aparición de aparatología preadjustada ha colaborado en la efectividad de los tratamientos de ortodoncia, pero para que la expresión de esta aparatología se logre, es necesario una correcta colocación de los brackets y la permanencia de estos en boca durante todo el tratamiento. La precisión en la colocación mejora con la técnica de cementado indirecta, ya que permite el acceso a las zonas posteriores, a lugares donde se ve disminuida la visión y además disminuye la condensación de aliento y contaminación salival. Si bien esta técnica requiere tiempo extra de laboratorio, es más rápida en la etapa clínica (AU)

Difference of Chemical Bonds Between UDMA Bonding Agents with Ethanol Solvent and Acetone Solvent on Dentin Collagen

ABSTRACT Objective: To investigate the difference of chemical bonds between urethane dimethacrylate (UDMA) bonding agents with ethanol solvent and acetone solvent on dentin collagen. Material and Methods: This experimental comparison study used three groups: G1 (Control): UDMA and collagen; G2: UDMA, collagen and ethanol; and G3: UDMA, collagen and acetone. The groups were then pelleted and analysed with FTIR, then the peak value of carbonyl absorption band from each study group was calculated. The result of FTIR analysis and the peak of carbonyl absorption band (P) was calculated using the formula: P = (BC / AB) X 100; AB. BC is measured in centimeters. The study of chemical bond differences between ethanol-solvent UDMA agents compared with acetone-solvent on dentin collagen resulted in a graph of peak of carbonyl absorption bands of UDMA and dentin collagen groups. To determine the chemical bonds of UDMA from the top of the carbonyl ester absorption bands with wavenumber absorption in range 1700-1750 cm-1, the decreasing peak of the carbonyl absorption bands is assumed as more chemical bonds that formed. Data were analysed using Anova one way and Tukey HSD test. Results: There were significant differences between the three study groups (p<0.05). Conclusion: UDMA bonding agents' chemical bonds with acetone solvent are much higher than the chemical bonds between UDMA bonding agents with ethanol solvent on dentin collagen.

Direct and Indirect Bonding Techniques: A Systematic Review

ABSTRACT Objective: To assess the scientific evidence on direct and indirect bonding techniques to analyse the differences related to treatment time, number of appointments and number of bracket detachments. Material and Methods: The MEDLINE and Cochrane Library databases were searched through to March 2021. Reference lists from the retrieved publications were also examined. The following article types that described data on the different types of direct and indirect bonding techniques in orthodontics were included: prospective and retrospective cohort studies, case-control studies and randomized controlled clinical trials (RCCTs). Two review authors independently assessed eligibility, extracted data, and ascertained the quality of the studies. Results: The search strategy initially resulted in 824 articles, and after a careful selection comprising the inclusion criteria, 12 articles were picked for the final review, specifically 2 cohort studies, 4 case-control studies and 6 RCCTs. The methodological quality was low in 4 studies, medium in 2, and high in 6 articles. Conclusion: The evidence currently available suggests that the use of computer-aided bonding is related to a reduction in treatment time and the number of appointments compared to direct and manual indirect bonding. However, the total bonding time for computer-aided bonding technique, including digital bracket placement, was longer than for direct bonding. Further high-quality RCTs on the differences between direct and indirect bonding are necessary to determine more precise data, as well as additional advantages and disadvantages.

High bonding strength between zirconia and composite resin based on combined surface treatment for dental restorations.

Zirconia is the preferred material for dental restorations; however, dental restorations are usually affected by zirconia fractures due to chipping and delamination of the veneer ceramic. One effective solution for repairing chemically inert zirconia frameworks is to strongly chemically bond them with the composite resin via surface modification. Thus, the bonding strength between the zirconia and composite resin determines the performance of dental restoration. Herein, we investigate the shear bond strength between zirconia ceramic and two ceramic repair systems before and after thermal cycling based on different surface pretreatments, including air-abrasion and a novel silane coupling agent. When treated with combined sandblasting, novel silane and 10-methacryloyloxydecyl hydrogen phosphate act as a bonding agent for the zirconia surface, and the maximum shear bond strength achieves 27.5 MPa, as measured by a universal testing machine through the average of 16 separate measurements. The results show that the combined treatment resists the interface damage caused by expansion and contraction during thermal cycling. The long-term bond durability is due to the micro-mechanical bond force formed by resin and ceramic, and the chemical bonds of Zr-O-Si at the interface. Results indicate that selective pretreating the surface results in high bond strength between the zirconia and the composite resin, which is meaningful to optimize dental restoration.

Zinc oxide and copper nanoparticles addition in universal adhesive systems improve interface stability on caries-affected dentin.

This study evaluated the MMP inhibition of the zinc oxide and copper nanoparticles (ZnO/CuNp), and the effects of their addition into adhesives on antimicrobial activity (AMA), ultimate tensile strength (UTS), in vitro degree of conversion (in vitro-DC), as well as, resin-dentin bond strength (µTBS), nanoleakage (NL) and in situ-DC on caries-affected dentin. Anti-MMP activity was evaluated for several MMPs. ZnO/CuNp (0% [control]; 5/0.1 and 5/0.2 wt%) were added into Prime&Bond Active (PBA) and Ambar Universal (AMB). The AMA was evaluated against Streptococcus mutans. UTS were tested after 24 h and 28d. After induced caries, adhesives and composite were applied to flat dentin surfaces, and specimens were sectioned to obtain resin-dentin sticks. µTBS, NL, in vitro-DC and in situ-DC were evaluated after 24 h. ANOVA and Tukey's test were applied (α = 0.05). ZnO/CuNp demonstrated anti-MMP activity (p < 0.05). The addition of ZnO/CuNp increased AMA and UTS (AMB; p < 0.05). UTS for PBA, in vitro-DC, in situ-DC and µTBS for both adhesives were maintained with ZnO/CuNp (p > 0.05). However, lower NL was observed for ZnO/CuNp groups (p < 0.05). The addition of ZnO/CuNp in adhesives may be an alternative to provide antimicrobial, anti-MMP activities and improves the integrity of the hybrid layer on caries-affected dentin.

Resin bond strength to zirconia: effects of surface treatments and resin cements.

This in vitro study evaluated the effect of surface treatments on the microshear bond strength between zirconia and 2 different resin cements. Thirty sintered zirconia blocks (15.5 × 19.0 × 39.0 mm) were allocated into 10 groups according to 2 factors: surface treatment (control [10% isopropyl alcohol], silica coating, primer, hot etching solution, or glaze) and resin cement (conventional dual-curing [Multilink Automix] or self-adhesive [RelyX U100]). Three cement cylinders (0.7-mm diameter × 1.5-mm height) were made on the surface of each zirconia block. The specimens were stored in water for 6 months at 37°C and then submitted to microshear bond strength tests (n = 9 per surface treatment group). The bond strength data were analyzed statistically with Kruskal-Wallis and Dunn tests (P < 0.05). The contact angle was measured with a goniometer on separate surface-treated disc specimens (n = 2 per group). The greatest mean (SD) bond strength values, regardless of cement type, were reported for the groups with the glaze surface treatment: conventional cement, 13.1 (0.26) MPa; and self-adhesive cement, 20.1 (0.23) MPa. The next greatest mean (SD) values were found in the silica coating groups: conventional cement, 7.94 (0.09) MPa; and self-adhesive cement, 9.8 (0.10) MPa. The self-adhesive cement groups presented the greatest bond strength values, except when the primer surface treatment was applied. The zirconia treated with the hot etching solution presented the greatest mean contact angle, 78.23 (SD 1.34) degrees, and bond strengths that were among the lowest achieved, suggesting that low wettability may have influenced bond strengths.

[Comparison of adhesive seal morphology between APC™ PLUS and APC™ Flash-Free Adhesive Coated brackets]. / Comparaison du joint de colle entre les attaches préencollées APC™ PLUS et les attaches APC™ Flash-Free.

INTRODUCTION: Does the new adhesive-coated APC™ Flash-Free bracket from the 3M Unitek® group simplify the bonding protocol without compromising precision? OBJECTIVES: The aim of this study was to compare the morphology of the adhesive joint between the classic APC™ PLUS adhesive-coated brackets and APC™ Flash-Free brackets. MATERIALS AND METHODS: In vitro bonding of esthetic brackets in the CLARITY™ ADVANCED range was performed to compare the morphology of the excess flash between APC™ PLUS and APC™ Flash-Free brackets. RESULTS: No statistically significant difference was found concerning the morphology of the excess flash between APC™ PLUS and APC™ Flash-Free brackets. A statistically significant difference was found regarding the thickness of the adhesive between the two types of bracket. The adhesive used for the APC™ Flash-Free brackets was significantly thicker than for the APC™ PLUS brackets (P=0.0001). Adhesive thickness was also more homogeneous on the APC™ Flash-Free brackets (P=0.001 for the relative difference). CONCLUSION: The adhesive is thicker but adhesive homogeneity is greater with APC™ Flash-Free brackets than with APC™ PLUS brackets.

Evaluation of the prototype of a new bracket-positioning gauge.

OBJECTIVE: The purposes of this study were to present a prototype of a bracket-positioning gauge, which makes vertical inclination of the instrument difficult, allowing a reduction of vertical bracket positioning error, and to test its accuracy in bracket positioning by groups of individuals with different clinical experience and in specific groups of teeth. METHODS: For the testing of the prototype, four groups of six participants each were used: Group 1 was composed of undergraduate students in the dental school, who had no previous experience in bonding orthodontic attachments; Group 2 was composed of orthodontic graduate students in the dental school; Group 3 consisted of orthodontists with a maximum of 5 years of clinical experience; Group 4 comprised orthodontists with more than 5 years of clinical experience. A typodont was simulated with a Class I crowded malocclusion, which reproduced the same occlusal characteristics for all groups to be bonded. All participants were instructed to bond 0.022×0.028-in Edgewise brackets on the labial surfaces of the upper and lower incisors, canines, and premolars at a height of 4 mm from the incisal edge or the labial cusp tip. RESULTS: Only the mean value of Group 1 showed statistically significant difference in the comparison with the standard measurement. In the groups of teeth, the difference was significant for the premolar and incisor groups. CONCLUSION: Clinical experience interfered with the accuracy of vertical positioning of orthodontic attachments. As for the groups of teeth, premolars, followed by canines and incisors had the closest mean values to the standard measurement.

Evaluation of the prototype of a new bracket-positioning gauge

ABSTRACT Objective: The purposes of this study were to present a prototype of a bracket-positioning gauge, which makes vertical inclination of the instrument difficult, allowing a reduction of vertical bracket positioning error, and to test its accuracy in bracket positioning by groups of individuals with different clinical experience and in specific groups of teeth. Methods: For the testing of the prototype, four groups of six participants each were used: Group 1 was composed of undergraduate students in the dental school, who had no previous experience in bonding orthodontic attachments; Group 2 was composed of orthodontic graduate students in the dental school; Group 3 consisted of orthodontists with a maximum of 5 years of clinical experience; Group 4 comprised orthodontists with more than 5 years of clinical experience. A typodont was simulated with a Class I crowded malocclusion, which reproduced the same occlusal characteristics for all groups to be bonded. All participants were instructed to bond 0.022×0.028-in Edgewise brackets on the labial surfaces of the upper and lower incisors, canines, and premolars at a height of 4 mm from the incisal edge or the labial cusp tip. Results: Only the mean value of Group 1 showed statistically significant difference in the comparison with the standard measurement. In the groups of teeth, the difference was significant for the premolar and incisor groups. Conclusion: Clinical experience interfered with the accuracy of vertical positioning of orthodontic attachments. As for the groups of teeth, premolars, followed by canines and incisors had the closest mean values to the standard measurement.

RESUMO Objetivos: os objetivos deste estudo foram apresentar um protótipo de posicionador de braquetes ortodônticos que dificulte a inclinação no sentido vertical, possibilitando a redução dos erros de altura no posicionamento desses acessórios; além de testar sua precisão na colagem, realizada por grupos de indivíduos com diferentes tempos de experiência clínica em Ortodontia e em grupos específicos de dentes. Métodos: para os testes do protótipo desenvolvido, quatro grupos de seis participantes foram formados. O Grupo 1 foi composto por alunos do curso de Odontologia sem qualquer prática com colagem em Ortodontia; o Grupo 2, por estudantes em Ortodontia; o Grupo 3, por ortodontistas com menos de cinco anos de experiência clínica; e o Grupo 4, por ortodontistas com mais de cinco anos de experiência clínica em Ortodontia. Em um typodont, foi simulada uma má oclusão Classe I com apinhamento, com as mesmas características para todas as colagens realizadas. Todos os participantes foram instruídos a colar braquetes Edgewise 0,022" x 0,028" na superfície vestibular dos incisivos, caninos e pré-molares superiores e inferiores, na altura de 4mm da borda incisal ou cúspide vestibular. Resultados: somente a média do Grupo 1 apresentou diferença estatisticamente significativa na comparação com a medida padrão. Nos grupos de dentes, a diferença foi significativa para o grupo dos pré-molares e incisivos. Conclusão: o tempo de experiência clínica interferiu na precisão do posicionamento vertical do acessório ortodôntico e, quanto aos grupos de dentes, as médias mais próximas à medida padrão foram dos pré-molares, seguidas pelos caninos e incisivos.

Dentin bond strength and nanoleakage of the adhesive interface after intracoronal bleaching.

This study evaluated dentin bond strength (BS) and nanoleakage of non- and pre-etched dentin immediately (T0 ,), 7 days (T7 ), and 14 days (T14 ) after bleaching. Bovine incisors (150) were selected and half of them submitted to intrapulpal dentin etching (e). Non- and pre-etched dentin were subjected to the following (n = 15): no bleaching/control (C); 35% carbamide peroxide (CP); 35% hydrogen peroxide (35% HP); 25% hydrogen peroxide (25% HP); and sodium perborate (SP). Bleaching agents were applied to the pulp chamber four times within a 72-h interval. Afterwards, pulp chamber dentin was prepared for the BS test at different evaluation times (n = 5): T0 , T7 , and T14 . Composite blocks were built on pulp chamber and sectioned in slices. Slices were reduced to an hour-glass shape with a cross-sectional area of 0.8 mm2 and submitted to microtensile BS test. Two additional specimens for each group were prepared for nanoleakage evaluation by transmission electron microscopy (TEM). Results were analyzed by ANOVA (two-way) and Dunnett's test (p < .05). BS decreased immediately after intracoronal bleaching for both sound and pre-etched dentin (p < .05). At T14 , the BS of non-etched bleached dentin increased for all groups, whereas the pre-etched SPe group presented BS similar to the Ce. Nanoleakage within the hybrid layer was perceptible immediately after bleaching, although a decrease in nanoleakage was observed for all groups at T14 . Adhesive restorations should be performed 7-14 days after bleaching, according to the bleaching agent used. Intracoronal bleaching should be performed preferably with sodium perborate if previous dentin etching is applied.

Laser Sintering Technology and Balling Phenomenon.

OBJECTIVE: The aim of this review was to evaluate the balling phenomenon which occurs typically in Selective Laser Sintering (SLS). BACKGROUND DATA: The balling phenomenon is a typical SLS defect, and observed in laser sintered powder, significantly reduces the quality of SLS, and hinders the further development of SLS Technology. METHODS: Electronic database searches were performed using Google Scholar. The keywords "laser sintering, selective laser sintering, direct metal laser melting, and balling phenomenon" were searched in title/abstract of publications, limited to December 31, 2016. The inclusion criteria were SLS, balling phenomenon, some alloys (such as Cr-Co, iron, stainless steel, and Cu-based alloys) mechanical properties, microstructure and bond strength between metal-ceramic crown, laboratory studies, full text, and in English language. RESULTS: A total of 100 articles were found the initial search and yielded a total of 50 studies, 30 of which did not fulfill the inclusion criteria and were therefore excluded. In addition, 20 studies were found by screening the reference list of all included publications. Finally, 40 studies were selected for this review. CONCLUSIONS: The method in question is regulated by powder material characteristics and the conditions of laser processing. The procedure of formation, affecting factors, and the mechanism of the balling effect are very complex.

Shear Bond Strength of Metal Brackets to Porcelain Using a Universal Adhesive.

INTRODUCTION: Bracket bonding to porcelain has high failure rate compared to bonding to enamel. AIM: This study aimed to assess the shear bond strength (SBS) of metal brackets to porcelain using a universal adhesive. MATERIAL AND METHODS: In this in vitro experimental study, 40 porcelain blocks (1x1x1 cm3)were divided into four groups (n=10). The porcelain surfaces were etched with 10% hydrofluoric (HF) acid and bonded to metal brackets using Transbond XT composite and the following bonding protocols: Transbond XT bonding agent alone in group 1, silane plus Transbond XT bonding agent in group 2, silane plus universal adhesive (G-Premio bond) in group 3 and universal adhesive alone in group 4. The SBS was measured using a universal testing machine at a crosshead speed of 1 mm/minute. Fracture surfaces were evaluated under a stereo microscope, and the adhesive remnant index (ARI) scores were determined. RESULTS: The highest and the lowest SBS values were noted in groups 3 (17.06±2.58 MPa) and 4 (9.85±4.76 MPa), respectively. Type of adhesive had no significant effect on SBS (P=0.611). However, the effect of application of silane on SBS was significant (P=0.000). Groups subjected to the application of silane showed higher SBS values than others. The mode of failure was mainly adhesive in groups 2 and 3, and adhesive and mixed in groups 1 and 4. The difference in ARI scores was statistically significant (P=0.016). CONCLUSION: Universal adhesive and Transbond XT were not significantly different in SBS. However, application of silane significantly increased the bond strength.

ZnCl2 Incorporated into Experimental Adhesives: Selected Physicochemical Properties and Resin-Dentin Bonding Stability.

The aim of this study was to evaluate the degree of conversion (DC%), water sorption (WS), solubility (SO), and resin-dentin bonding stability of experimental adhesive systems containing ZnCl2. Different concentrations (wt.%) of ZnCl2 were added to a model etch-and-rinse adhesive system consisting of BISGMA, HEMA, UDMA, GDMA, water, and ethanol: Zn0 (0%-control group); Zn2 (2%); Zn3.5 (3.5%); and Zn5 (5%). Adper Single Bond 2 (SB) was used as commercial reference. The samples were light cured for 20s using a quartz-tungsten-halogen unit (650 mW/cm2). DC% (n = 5) was measured using FT-IR spectroscopy, and WS and SO (n = 5) were calculated based on ISO4049. Microtensile bond strength (µTBS) and nanoleakage (NL) were measured after 24 h and 12 months of water storage (n = 10). Data were analyzed using ANOVA and Tukey's HSD test (5%). Zn5 presented the lowest DC% and the highest WS and SO (p < 0.05). Zn0 and Zn2 presented statistically similar DC%, WS, SO, and immediate µTBS. All adhesives containing ZnCl2 maintained a µTBS stability after 12 months, but only Zn2 and Zn3.5 did not suffer an increase in NL. SB presented the highest immediate µTBS but the greatest reduction after 12 months (p < 0.05). The addition of 2 wt.% of ZnCl2 in adhesive formulations seems to be a promising way to improve the resin-dentin bonding stability. Higher concentrations than 2 wt.% could impair some physicochemical properties.

Dental Hygiene and Orthodontics: Effect of Ultrasonic Instrumentation on Bonding Efficacy of Different Lingual Orthodontic Brackets.

Dental hygienists are often faced with patients wearing lingual orthodontic therapy, as ultrasonic instrumentation (UI) is crucial for oral health. As the application of external forces can lead to premature bonding failure, the aim of this study was to evaluate the effect of UI on shear bond strength (SBS) and on adhesive remnant index (ARI) of different lingual orthodontic brackets. 200 bovine incisors were divided into 10 groups. Four different lingual (STB, Ormco; TTR, Rocky Mountain Orthodontics; Idea, Leone; 2D, Forestadent) and vestibular control (Victory, 3M) brackets were bonded. UI was performed in half of specimens, whereas the other half did not receive any treatment. All groups were tested with a universal testing machine. SBS and ARI values were recorded. Statistical analysis was performed (significance: P = 0.05). TTR, Idea, and 2D lingual brackets significantly lowered SBS after UI, whereas for other braces no effect was recorded. Appliances with lower mesh area significantly reduced their adhesion capacity after UI. Moreover groups subjected to UI showed higher ARI scores than controls. UI lowered SBS of lingual appliances of small dimensions so particular care should be posed avoiding prolonged instrumentation around bracket base during plaque removal. Moreover, UI influenced also ARI scores.

Improvement of Total Etching Dentin Bonding with Subpressure.

This study aimed to investigate the effects of subpressure on the bond properties of total-etching adhesive to dentin. Thirty-six caries-free premolars were sectioned parallel to the occlusal plane and randomly divided into four groups (n = 9): a control group (C, no treatment) and three subpressure groups, which were treated under 0.8, 0.6 or 0.4 bar after applying adhesives, named S8, S6 and S4, respectively. Afterward, resin was bonded to the dentin surface, and 27 beams (1.0 mm × 1.0 mm) of each group were sectioned. One was selected to observe the bonding interface from each group by SEM. Each group was divided into two subgroups (n = 13): 24 hours of water storage (I) and 10,000 thermocycling (A). The microtensile bond strength (µTBS), failure modes and nanoleakage expression were evaluated. SEM results showed that the subpressure groups had longer and denser resin tags. The µTBS of the subpressure groups was higher than that of the control group (p < 0.05). The subpressure groups were dominated by mixed failure, whereas main interfacial failure appeared in group C. The subpressure groups showed less silver deposition than the control group (p < 0.05). The subpressure technique may remarkably improve bonding strength and decrease nanoleakage on total-etching bonding.

Comparison of two methods of visual magnification for removal of adhesive flash during bracket placement using two types of orthodontic bonding agents

ABSTRACT Objective: This study aimed to evaluate the effectiveness of two methods of visual magnification (operating microscope and light head magnifying glass) for removal of composite flash around orthodontic metal brackets. Material and Methods: Brackets were bonded in the center of the clinical crown of sixty well-preserved human premolars. Half of the sample was bonded with conventional Transbond XT (3M Unitek TM, USA), whereas the other half was bonded with Transbond TM Plus Color Change (3M Unitek TM, USA). For each type of composite, the choice of method to remove the flash was determined by randomly distributing the teeth into the following subgroups: A (removal by naked eye, n = 10), B (removal with the aid of light head magnifying glass, under 4x magnification, n = 10), and C (removal with the aid of an operating microscope, under 40x magnification, n = 10). Brackets were debonded and teeth taken to a scanning electron microscope (SS-x-550, Shimadzu, Japan) for visualization of their buccal surface. Quantification of composite flash was performed with Image Pro Plus software, and values were compared by Kruskal-Wallis test and Dunn’s post-hoc test at 5% significance level. Results: Removal of pigmented orthodontic adhesive with the aid of light head magnifying glass proved, in general, to be advantageous in comparison to all other methods. Conclusion: There was no advantage in using Transbond TM Plus Color Change alone. Further studies are necessary to draw a more definitive conclusion in regards to the benefits of using an operating microscope.

RESUMO Objetivo: este estudo teve o objetivo de avaliar a eficácia de dois métodos de magnificação visual (microscópio cirúrgico e lupa de pala) para remoção da resina residual em torno de braquetes ortodônticos metálicos. Material e Métodos: os braquetes foram colados no centro da coroa clínica de 60 pré-molares humanos bem preservados. Metade da amostra foi colada com Transbond XT convencional (3M UnitekTM, EUA), enquanto a outra metade foi colada com TransbondTM Plus Color Change (3M-UnitekTM, EUA). Para cada tipo de resina, a escolha do método para remover o resíduo foi determinada por meio da distribuição aleatória dos dentes nos seguintes subgrupos: A (remoção a olho nu, n = 10), B (remoção com a ajuda de lupa de pala, sob uma ampliação de 4x, n = 10) e C (remoção com auxílio de um microscópio cirúrgico, sob uma ampliação de 40x, n = 10). Os braquetes foram descolados e os dentes, levados a um microscópio eletrônico de varredura (SS-X-550, Shimadzu, Japão) para visualização de sua superfície vestibular. A quantificação da resina residual foi realizada por meio do software Image Pro Plus, onde os valores foram comparados utilizando-se o teste de Kruskal-Wallis e o teste post-hoc de Dunn, ao nível de significância de 5%. Resultados: a remoção da resina ortodôntica pigmentada com o auxílio da lente de aumento de pala provou, em geral, ser mais vantajosa, em comparação aos outros métodos testados. Conclusão: não houve vantagem em se usar a TransbondTM Plus Color Change sozinha. Estudos adicionais são necessários para se chegar a uma conclusão definitiva sobre os benefícios da utilização de microscópio cirúrgico.